Call Us+919820225982
Edwards EXT 70 Turbo Vacuum Pump, DN 63 ISO, B72205000 / HPG 1946 80002

Edwards EXT 70 Turbo Vacuum Pump, DN 63 ISO, B72205000 / HPG 1946 80002

Product Details:


Price And Quantity

  • 1 Piece
  • 5000 INR

Trade Information

  • 5-10 Piece piece Per Month
  • 6-8 Week

Product Description

dwards EXT 70 Turbo Vacuum Pump, DN 63 ISO, B72205000 / HPG 1946 80002

Unit is fully rebuilt and comes with a FULL 6-MONTH WARRANTY!

General Overview:

The EXT70H, EXT70Hi, EXT250H and EXT250Hi pumps are compound vacuum pumps that combine a turbomolecular pump and a drag pump on a single shaft.

The turbomolecular pump is made from a multi-stage axial-flow turbine which is optimised for operation in molecular flow conditions. The drag pump is made from pumping channels formed by plane rotating disks. The drag pump is designed for operation at higher pressures than conventional turbomolecular pumps.

The light alloy rotor is machined from one piece to form the angled blades of the turbomolecular pump and the disks of the drag pump. The rotor blades rotate between angled stator blades which are supported by spacer rings. The rotor and stator blades have an open structure at the pump inlet, and a more closed structure at the outlet. This configuration gives an optimum combination of pumping speed and compression when pumping gases of both high and low molecular weight. For the blades to be effective, their speed must be close to the thermal velocity of the gas. The rotor of the EXT70H/Hi therefore rotates at up to 90000 r min-1, and the rotor of the EXT250H/Hi therefore rotates at up to 60000 r min-1.

Gas from the inlet is compressed through each of the bladed stages of the turbomolecular pump and transferred to the drag pump. In the drag pump stages, the gas is further compressed as it is pumped around the channels formed by the separation of the disks. The inlet and outlet of each channel is separated by a close-running seal which diverts the gas through a port to the next channel, or to the pump outlet.

The rotating assembly is supported at the inlet end by a frictionless magnetic bearing and by a precision ceramic ball bearing at the outlet end. The ball bearing is lubricated from an oil reservoir and wick mechanism.

The EXT pump is supplied with an inlet-screen fitted in the bore of the inlet-flange. The EXT250Hi pump is also supplied with an inlet-strainer which fits in the interstage-port. The inlet-screen and inlet-strainer protect the pump against damage which would be caused by debris which enters the pump. The inlet-screen also protects you from the sharp blades in the pump.

The EXT pump has a vent-port that you can use to vent the pump and your vacuum system to atmospheric pressure. The vent-port introduces vent gas part way up the pump rotor; this ensures maximum cleanliness. The pump is supplied with a manual vent-valve fitted to the vent-port.

The EXT250H and EXT250Hi pumps have a purge-port in the motor and bearing housing chamber. In order to protect the bearing lubricant from the effects of high oxygen concentrations, you can introduce an inert purge gas through the purge-port. You can fit an optional vent-port adaptor and purge restrictor to the purge-port to control the flow rate of the purge gas and to filter the gas supply.


Technical Data:

Maximum inlet-flange temperature100 C
Maximum magnetic field5 mT
Installation categoryEN61010 part 1, Category 1
Pollution degreeCAN/CSA, UL, EN 61010 part 1
Altitude2000 m
Humidity10 to 90% non condensing
Electrical supply80 V d.c.
Equipment typeFixed equipment, for indoor use only


Enter Buying Requirement Details
Email Id
Mobile number

Back to top